Adafruit Si4713/IDE not working

Question

My IDE shows "Adafruit Radio - Si4713 Test", but without "RDS on!", which is supposed to show up. The radio I use (Inscabin M60) shows static. Am I doing something wrong?

Adafruit Radio - Si4713 Test Couldn't find radio? Adafruit Radio - Si4713 Test Couldn't find radio? Adafruit Radio - Si4713 Test Couldn't find radio? Adafruit Radio - Si4713 Test Couldn't find radio Adafruit Radio - Si4713 Test The italic represents where I made a mistake. This is the code, where I only changed the error message. I previously changed the #define FMSTATION to 9670, but KTCK has taken that signal, so I changed it back. /*************************************************** This is an example for the Si4713 FM Radio Transmitter with RDS

Designed specifically to work with the Si4713 breakout in the adafruit shop ----> https://www.adafruit.com/products/1958

These transmitters use I2C to communicate, plus reset pin. 3 pins are required to interface Adafruit invests time and resources providing this open source code, please support Adafruit and open-source hardware by purchasing products from Adafruit!

Written by Limor Fried/Ladyada for Adafruit Industries.
BSD license, all text above must be included in any redistribution

Many thx to https://github.com/phrm/fmtx/blob/master/firmware/firmware.ino !

****************************************************/

#include <Wire.h>
#include <Adafruit_Si4713.h>
#define _BV(n) (1 << n)
#define RESETPIN 12
#define FMSTATION 10230      // 10230 == 102.30 MHz
Adafruit_Si4713 radio = Adafruit_Si4713(RESETPIN);
void setup() {
  Serial.begin(9600);
  Serial.println("Adafruit Radio - Si4713 Test");
if (! radio.begin()) {  // begin with address 0x63 (CS high default)
    Serial.println("Couldn't find radio");
    while (1);
  }
// Uncomment to scan power of entire range from 87.5 to 108.0 MHz
  /*
  for (uint16_t f  = 8750; f<10800; f+=10) {
   radio.readTuneMeasure(f);
   Serial.print("Measuring "); Serial.print(f); Serial.print("...");
   radio.readTuneStatus();
   Serial.println(radio.currNoiseLevel);
   }
   */
Serial.print("\nSet TX power");
  radio.setTXpower(115);  // dBuV, 88-115 max
Serial.print("\nTuning into "); 
  Serial.print(FMSTATION/100); 
  Serial.print('.'); 
  Serial.println(FMSTATION % 100);
  radio.tuneFM(FMSTATION); // 102.3 mhz
// This will tell you the status in case you want to read it from the chip
  radio.readTuneStatus();
  Serial.print("\tCurr freq: "); 
  Serial.println(radio.currFreq);
  Serial.print("\tCurr freqdBuV:"); 
  Serial.println(radio.currdBuV);
  Serial.print("\tCurr ANTcap:"); 
  Serial.println(radio.currAntCap);
// begin the RDS/RDBS transmission
  radio.beginRDS();
  radio.setRDSstation("AdaRadio");
  radio.setRDSbuffer( "Adafruit g0th Radio!");
Serial.println("RDS on!");
radio.setGPIOctrl(_BV(1) | _BV(2));  // set GP1 and GP2 to output
}
void loop() {
  radio.readASQ();
  Serial.print("\tCurr ASQ: 0x"); 
  Serial.println(radio.currASQ, HEX);
  Serial.print("\tCurr InLevel:"); 
  Serial.println(radio.currInLevel);
  // toggle GPO1 and GPO2
  radio.setGPIO(_BV(1));
  delay(500);
  radio.setGPIO(_BV(2));
  delay(500);
}